Hello, welcome to All-trust WD (Suzhou) Intelligent Technology Co., Ltd. official website!
◆ Optimized output bearing
◆ Simple installation
◆ Low calorific value
This PLQE is simple in structure and powerful in function. It can be directly connected to the equipment without intermediate flange. The deep groove ball bearing with larger size at the output end can withstand higher radial force and axial force. At the same time, it only generates very low heat, and can operate safely and reliably even in the production cycle with high requirements.
characteristic
The heat release is still very low at high speed
Optimized output bearing
Square output flange
High dynamics in multi axis systems
Can be installed anywhere
Precise engagement
| Reducer parameters | PLQE060 | PLQE080 | PLQE120 | P | |
| transmission ratio | 3, 4, 5, 7, 8, 10 | one | |||
| 9, 12, 15, 16, 20, 25, 32, 40, 64 | two | ||||
| 60, 80, 100, 120, 160, 200, 256, 320, 512 | three | ||||
| service life | h | thirty | |||
| Efficiency at full load | % | 98/97/92 | |||
| Minimum operating temperature/maximum operating temperature | ℃ | -25/90 | |||
| Degree of protection | IP54 |
||||
| Standard lubrication | Grease (lifetime lubrication) | ||||
| Food grade lubrication | Grease (lifetime lubrication) | ||||
| Low temperature lubrication | Grease (lifetime lubrication) | ||||
| Installation position | arbitrarily | ||||
| Standard return clearance | arcmin | <10-<15 | <7-<11 | <7-<11 | |
| Torsional stiffness | Nm/arcmin | 2.8-4.1 | 8.5-13.4 | 14.0-19.0 | |
| Weight of reducer | kg | 1.1-1.5 | 2.7-4.0 | 6.4-10.1 | |
| Standard box surface | Box: steel - oxidized after heat treatment (black) |
||||
| Running noise | dB/(A) | fifty-eight | sixty | sixty-five | |
| Maximum bending moment based on reducer input flange |
Nm | three | eight | sixteen | |
Rated output torque
| PLQE060 | PLQE080 | PLQE120 | I | P |
| twenty-eight | eighty-five | one hundred and fifteen | three | one |
| thirty-eight | one hundred and fifteen | one hundred and fifty-five | four | |
| forty | one hundred and ten | one hundred and ninety-five | five | |
| twenty-five | sixty-five | one hundred and thirty-five | seven | |
| eighteen | fifty | one hundred and twenty | eight | |
| fifteen | thirty-eight | ninety-five | ten | |
| forty-four | one hundred and thirty | two hundred and ten | nine | two |
| forty-four | one hundred and twenty | two hundred and sixty | twelve | |
| forty-four | one hundred and ten | two hundred and thirty | fifteen | |
| forty-four | one hundred and twenty | two hundred and sixty |
sixteen | |
| forty-four | one hundred and twenty | two hundred and sixty | twenty | |
| forty | one hundred and ten | two hundred and thirty | twenty-five | |
| forty-four | one hundred and twenty | two hundred and sixty | thirty-two | |
| forty | one hundred and ten | two hundred and thirty | forty | |
| eighteen | fifty | one hundred and twenty | sixty-four | |
| forty-four | one hundred and ten | two hundred and sixty | sixty | three |
| forty-four | one hundred and twenty | two hundred and sixty | eighty | |
| forty-four | one hundred and twenty | two hundred and sixty | one hundred | |
| forty-four | one hundred and ten | two hundred and thirty | one hundred and twenty | |
| forty-four | one hundred and twenty | two hundred and sixty | one hundred and sixty | |
| forty | one hundred and ten | two hundred and thirty | two hundred | |
| forty-four | one hundred and twenty | two hundred and sixty | two hundred and fifty-six | |
| forty | one hundred and ten | two hundred and thirty | three hundred and twenty | |
| eighteen | fifty | one hundred and twenty | five hundred and twelve |
Output shaft load
| Output shaft load | PLQE060 | PLQE080 | PLQE120 | |
| Radial force of 20000h/radial force of 30000h |
N | 700-900 | 1700-2050 | 2400-2950 |
| Axial force of 20000h/axial force of 30000h | N | 800-1000 | 2000-2500 | 2100-2500 |
| 20000 h tilting moment | Nm | thirty-seven | one hundred and two | two hundred and thirty-two |
Geometric dimensions
| PLQE060 | PLQE080 | PLQE120 | Grade | ||
| Output shaft diameter | mm | sixteen |
twenty | twenty-five | |
| Diameter of output retaining lug | mm | sixty | eighty | one hundred and ten | |
| Box diameter | mm | sixty | eighty | one hundred and fifteen | |
| OUTSIDE OF OUTPUT FLANGE | mm | seventy | ninety | one hundred and fifteen | |
| Total length | mm |
one hundred and eleven | one hundred and forty-five | two hundred and one point five | one |
| one hundred and twenty-three point five | one hundred and sixty-two point five | two hundred and twenty-nine point five |
two | ||
| one hundred and thirty-six | one hundred and eighty | two hundred and fifty-seven | three | ||
| Output shaft length | mm | thirty-two | forty | fifty-five |
Copyright © All rights reserved by Zhongxin Weichuang (Suzhou) Intelligent Technology Co., LtdSUICPB No. 19054578
